Selective Pallet Rack Guide

While this guide is meant to assist you in choosing your rack, it is still beneficial to consult with one of our professional solutions specialists. They have been working with this material every day for years and are aware of ALL the tips and tricks concerning pallet racks.

Please feel free to call us at 800-598-5532 to discuss your planned layout.

Pallet Racks Overview

Selective Pallet racking is by far the most common type of warehouse storage rack and is the product typically thought of when the need arises for industrial type storage racking. All selective rack is made from component pieces that are usually priced & purchased seperately.

Pallet Rack Uprights

Uprights (also called Frames, or less commonly, legs) are the support columns that hold up individual shelves in a section of rack. Pallet Rack uprights form the ends of what are commonly known as ‘bays’ of pallet racking. Each pallet rack bay must have at least two uprights, however if multiple bays will be placed in a row they may share uprights (see figure 1).

Pallet Rack Beams

Beams are used to create the actual ‘shelf levels’ that support loads and are held up by pallet rack uprights. Pairs of beams form each individual shelf level (see figure 1). Shelf capacity is determined by the height of the beam, length of the beam and the number of shelves per bay. Most modern beams feature end clips that attach directly to the upright without the use of specialized hardware, however there are many different brands available that feature unique designs (see section below on selective rack brands.)

Pallet Rack Assembly – Putting it all together

Now that you’re familiar with the individual components, let’s take a look at configuring a rack installation that’s right for you.

Step 1: Size the product

The first step in determining what is needed is to size the product to be stored. The product’s width, depth and height are important to know, however you must also include the height, depth and width of your pallet if you are using them (see figure 2). In addition to the size of the product, the maximum weight of the product must also be determined. These measurements are key to determining the correct rack for your needs.

Step 2: Rows & Bays

Most often, static racks are configured in rows to make maximum use of available space. Rows can be configured in single or double (back to back) runs (see figure 3). The number of rows created will be determined by the width of the bays needed (see figure 1).

 Determining the width of the bays is accomplished by using the product measurements taken in Step 1. A good rule of thumb is to add 6″ to the width of each load to get overall bay width (also beam length – see below.) For example, if the product width is 42″ and is to be stored as two pallets per shelf, this is the correct equation: (42+6) x 2 = 96″ wide bays. To determine the depth of your uprights, subtract 6″ from the depth of the product to allow the proper pallet overhang. For example, if the pallets are 48″ deep, subtracting 6″ gives an upright depth of 42″. This overhang is adequate to insure that the weight of the product will be evenly distributed on the beams however, a lesser overhang is allowable as a function of aesthetics. If this is the case be sure that the pallets are in good condition. In this situation we would also recommend the use of additional supports; ie. Pallet Supports or Wire Decking (see figure 5 below).  As mentioned above, the beam length will be the exact same as the width of the bays. The length of beams is always measured from the insides of the upright frames.

Step 3: Shelf Spacing & Overall Rack Height

To find the overall rack height, again use the load measurements taken at the beginning. To each load, add 6″ to get the distance between shelves. The beam height will also need to be accounted for here and a rough estimate of 4″, 5″ or 6″ per shelf level (depeding on shelf capacity needed) will leave enough room for the beams. An equation to use for this height would read as follows:

((Load Height + 6″) x # of Shelves) + ([4", 5" or 6"] x # of Shelf Levels) = Upright Height

PLEASE NOTE:  The top of the upright should be more than 1/2 the height of the pallet + load to prevent loads from tipping over and falling off the rack. The bottom of the top load should never be at the top of the upright.

Other items to take into account when determining the overall rack height are the overall height of the ceiling, sprinkler system, lights and any other obstructions. Make sure to also account for the maximum reach of the lift truck that will retrieve the pallets. Also of note when determining aisle width is the turning radius of the lift truck.

Step 4: Rack Accessories

 A Note About Wire Decking

Wire Decking is typically used as a “fail-safe” when used in conjunction with static pallet rack. If you have pallets loaded with loose boxes, cartons or other materials the decking will act to catch items knocked off of the pallet to prevent injury to persons on the ground (provided the items are no smaller than the deck’s mesh size). Wire decking will also not prevent an item from falling off the front or back of the racking system. Although wire decking can be used as a “shelf level” to hold assorted goods, please note that most wire decks are NOT RATED FOR POINT LOADING. What this means is that if a deck’s overall capacity rating is 2000#, the deck will support a 2000# load evenly distributed over the entire surface of the deck. The palletized load must still be entirely supported by the front and rear pallet rack beams.

Pallet Rack Identification Guide

Below are some of the most common types of pallet racking found today. If you have something not on this list, please contact us at 800-598-5532 and we’ll be happy to help you identify it.

Teardrop	Interlake (New Style)	Structural
Ridg-U-Rak	Sturdibuilt	Speedrack
T-Bolt	Republic	Hiline
Unarco II	Paltier	Palmer Shile
Husky	Prest	Slide & Lock
Frick Gallagher	Amrack	Mirak
Penco	Burtman	Dexion
EMI